Accessories & Cable Assemblies

Adjustable Compression Fittings

The standard jack Circuit Box is available from one to six jacks and in two materials. Standard material jacks are good to 400 degrees Fahrenheit. High temperature jacks are good to 800 degrees Fahrenheit. All high temperature jacks are color coded 'red.' All standard jacks are coded per thermocouple calibration. 
The miniature jack Circuit Box (not shown) is available with two from to six jacks. All jacks are marked with thermocouple calibration, color coded and numbered. These jacks are good to 400 degrees Fahrenheit.

Circuit Boxes

This Explosion Proof (EP) instrument housing accommodates large diameter assemblies. multi-level circuit boards, and/or wide angle readouts and displays. Providing maximum clearance to facilitate instrument mounting, calibration, or service. Precision machined from sand-cast, copper-free aluminum. 
This housing is used for mounting the Fl 1-40 or Fl 1- 50 Series Transmitters. See our fully assembled and functional F7-LCD-SP which utilizes this head.

Conduit Explosion Proof (EP) Conduit Head w/ Window

Digital Displays & Controllers

Explosion Proof (EP) & Atex Approved Conduit Heads

Our Thermocouple Extension Assemblies feature #20 gage fiberglass insulated wire with flexible stainless steel armor. Solid #20 gage thermocouple grade wires are used for thermocouple types E, J, K, and T. Extension grade #20 gage solid wires are used for types Rx, Sx, Bx, and Cx thermocouples. Other insulation types are available, contact factory with your specify requirement (standard length "Y" is 36 inches -±1 inch). 

Extention Assemblies

Flip Top Conduit Heads

General Purpose Conduit Heads

The F7-LCD is a head mounted digital indicator, including a non-isolated Fl 1-40 Temperature Transmitter. Both the LCD display and the temperature transmitter are installed within an aluminum general purpose connector head. The connector head has a polycarbonate viewing window. The indicator has 1/2 inch high-contrast LCD digits. The connector head has 1/2 NPT process threads and 3/4 NPT conduit connection. Both NPT dimensions can be reduced to accommodate your requirement. Temperature transmitter programming performed by Nanmac Corporation. 

Head Mount Digital Displays w/ 4-20 mAmp Transmistters Installed

The F7-LCD-SP indicator is a heavy-duty LCD indicator installed within a NEMA 4 housing and includes an isolated, EX rated temperature transmitter with 4-20 mAmp output. 
Designed for field mounting, it utilizes a rugged, IP66 / NEMA 4 splash proof housing. 
All programming of the installed temperature transmitter is done at the factory. The user simply connects the required loop power (see F11-50 for full specifications). 
The actual transmitter used for this requirement is the F11-50 series, except it has EX rating. Temperature ranges and input loop power requirements are the same. For general use requirements that do not need isolated inputs. EX rating and NEMA enclosures, please see the F7-LCD device. 

Heavy Duty Head Mount Indicators w/ 4-2 mAmp Transmistter Installed

Isolated Head Mount Transmitters

Isolated Rail Mount Transmitters

Available in two materials, the standard material is good to 400 degrees Fahrenheit. The high temperature material is good to 800 degrees Fahrenheit. All high temperature jacks are color coded 'red.' All standard jacks are coded per thermocouple calibration. Standard thermocouple calibration symbols and color codes are easily visible from the front.

Jack Panels

Miniature Plugs & Jacks

Miniature Weather Proof Conduit Heads

All pre-machined receptacles have a two inch diameter and length "L' as specified. You only need to machine two inch holes in your mixer wall. Then, install the required receptacle. All this finesse machining has been done to the receptacle threads, through-hole, conical taper, etc. 
Stainless steel 316 receptacle (MDA series) designed to be welded into mixer wall. Available with dimension "L' from 1-1/4 to 4-1/2 inches increments of 1/4 inch. The MDA series mixer thermocouple requires one teflon conical seal (Part No. C11-60). 
Stainless Steel 303 spacer (MDA series) for use with MDA series receptacles. Available with dimension "L' from 1/4 to 3-1/4 inches increments of 1/4 inch. Spacer length "L.' is always 1-1/4 inches shorter than dimension "L' of receptacle. This spacer is not required if dimension "L' of MDA series receptacle is 1-1/4 inches. 
Stainless steel 316 receptacle (MCR series) designed to be welded into mixer wall. Available with dimension "L' from 1-1/4 to 4-1/2 inches increments of 1/4 inch. The MCR series mixer thermocouple requires one teflon conical seal (Part No. C11-70).

Mixer Temperature Sensor Mounting Accessories

Our RTD cable assemblies feature either fiberglass (FIB) insulation rated at 900 degrees Fahrenheit or teflon (TEF) insulation rated at 400 degrees Fahrenheit. Available in two, three, or four conductors. The standard plugs and jacks are rated to a continuous 400 degrees Fahrenheit. 

RTD Cable Assemblies

Standard 2 Pole & 3 Pole Connectors

Standard Head Mounted Transmitters

Standard Rail Mount Transmitters

The H34-540 Series is 1/16 DIN or 1/4 DIN temperature controller with auto tuning PID control capabilities. One of four user programmable set points may be selected. For PID control in the form of time proportional relay on/off output, time proportional voltage pulse, or 4-20 mAmp signal control. Its universal input accepts 23 inputs varieties, including thermocouple, RTD, and voltage inputs can be easily configured for a 4-20 mAmp input. The relays may be programmed as alarms with 20 different high, low, and deviation alarm types which can include fail-safe operation. Digital input options add the ability of external contacts to operate the controller. With RS-485 serial communication options include protocols for master/slave set point control, modbus ASCII and RTU. 
The H34-550 Series is 1/16 DIN or 1/4 DIN ramp and soak controller with auto-tuning PID control capabilities. Two programs store 15 segments each for precision set point control. At the completion of a program, the controller can hold a set point, stop the outputs, or loop the completion of a program. Thus, enabling one 30 segment program to be used. Its universal input accepts 23 inputs varieties, including thermocouple, RTD, and voltage inputs can easily be configured for a 4-20 mAmp input. The relays may be programmed as alarms with 20 different high, low, and deviation alarm types which include fail-safe operation. Digital input options add the ability of external contacts to operate the controller and digital output options are available. With RS-485 serial communication options include protocols for master/slave set point control, modbus ASCII and RTU. 